Pileus Git - ~andy/linux/blob - arch/arm/mach-at91/board-rm9200ek.c

   1 /*
   2  * linux/arch/arm/mach-at91/board-rm9200ek.c
   3  *
   4  *  Copyright (C) 2005 SAN People
   5  *
   6  *  Epson S1D framebuffer glue code is:
   7  *     Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
   8  *
   9  * This program is free software; you can redistribute it and/or modify
  10  * it under the terms of the GNU General Public License as published by
  11  * the Free Software Foundation; either version 2 of the License, or
  12  * (at your option) any later version.
  13  *
  14  * This program is distributed in the hope that it will be useful,
  15  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  16  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  17  * GNU General Public License for more details.
  18  *
  19  * You should have received a copy of the GNU General Public License
  20  * along with this program; if not, write to the Free Software
  21  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  22  */
  23
  24 #include <linux/types.h>
  25 #include <linux/gpio.h>
  26 #include <linux/init.h>
  27 #include <linux/mm.h>
  28 #include <linux/module.h>
  29 #include <linux/platform_device.h>
  30 #include <linux/spi/spi.h>
  31 #include <linux/mtd/physmap.h>
  32
  33 #include <asm/setup.h>
  34 #include <asm/mach-types.h>
  35 #include <asm/irq.h>
  36
  37 #include <asm/mach/arch.h>
  38 #include <asm/mach/map.h>
  39 #include <asm/mach/irq.h>
  40
  41 #include <mach/hardware.h>
  42 #include <mach/board.h>
  43 #include <mach/at91rm9200_mc.h>
  44 #include <mach/at91_ramc.h>
  45
  46 #include "generic.h"
  47
  48
  49 static void __init ek_init_early(void)
  50 {
  51         /* Initialize processor: 18.432 MHz crystal */
  52         at91_initialize(18432000);
  53 }
  54
  55 static struct macb_platform_data __initdata ek_eth_data = {
  56         .phy_irq_pin    = AT91_PIN_PC4,
  57         .is_rmii        = 1,
  58 };
  59
  60 static struct at91_usbh_data __initdata ek_usbh_data = {
  61         .ports          = 2,
  62         .vbus_pin       = {-EINVAL, -EINVAL},
  63         .overcurrent_pin= {-EINVAL, -EINVAL},
  64 };
  65
  66 static struct at91_udc_data __initdata ek_udc_data = {
  67         .vbus_pin       = AT91_PIN_PD4,
  68         .pullup_pin     = AT91_PIN_PD5,
  69 };
  70
  71 #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
  72 static struct at91_mmc_data __initdata ek_mmc_data = {
  73         .det_pin        = AT91_PIN_PB27,
  74         .slot_b         = 0,
  75         .wire4          = 1,
  76         .wp_pin         = AT91_PIN_PA17,
  77         .vcc_pin        = -EINVAL,
  78 };
  79 #endif
  80
  81 static struct spi_board_info ek_spi_devices[] = {
  82         {       /* DataFlash chip */
  83                 .modalias       = "mtd_dataflash",
  84                 .chip_select    = 0,
  85                 .max_speed_hz   = 15 * 1000 * 1000,
  86         },
  87 #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
  88         {       /* DataFlash card */
  89                 .modalias       = "mtd_dataflash",
  90                 .chip_select    = 3,
  91                 .max_speed_hz   = 15 * 1000 * 1000,
  92         },
  93 #endif
  94 };
  95
  96 static struct i2c_board_info __initdata ek_i2c_devices[] = {
  97         {
  98                 I2C_BOARD_INFO("ics1523", 0x26),
  99         },
 100         {
 101                 I2C_BOARD_INFO("dac3550", 0x4d),
 102         }
 103 };
 104
 105 #define EK_FLASH_BASE   AT91_CHIPSELECT_0
 106 #define EK_FLASH_SIZE   SZ_8M
 107
 108 static struct physmap_flash_data ek_flash_data = {
 109         .width          = 2,
 110 };
 111
 112 static struct resource ek_flash_resource = {
 113         .start          = EK_FLASH_BASE,
 114         .end            = EK_FLASH_BASE + EK_FLASH_SIZE - 1,
 115         .flags          = IORESOURCE_MEM,
 116 };
 117
 118 static struct platform_device ek_flash = {
 119         .name           = "physmap-flash",
 120         .id             = 0,
 121         .dev            = {
 122                                 .platform_data  = &ek_flash_data,
 123                         },
 124         .resource       = &ek_flash_resource,
 125         .num_resources  = 1,
 126 };
 127
 128 static struct gpio_led ek_leds[] = {
 129         {       /* "user led 1", DS2 */
 130                 .name                   = "green",
 131                 .gpio                   = AT91_PIN_PB0,
 132                 .active_low             = 1,
 133                 .default_trigger        = "mmc0",
 134         },
 135         {       /* "user led 2", DS4 */
 136                 .name                   = "yellow",
 137                 .gpio                   = AT91_PIN_PB1,
 138                 .active_low             = 1,
 139                 .default_trigger        = "heartbeat",
 140         },
 141         {       /* "user led 3", DS6 */
 142                 .name                   = "red",
 143                 .gpio                   = AT91_PIN_PB2,
 144                 .active_low             = 1,
 145         }
 146 };
 147
 148 static void __init ek_board_init(void)
 149 {
 150         /* Setup the LEDs */
 151         at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
 152
 153         /* Serial */
 154         /* DBGU on ttyS0. (Rx & Tx only) */
 155         at91_register_uart(0, 0, 0);
 156
 157         /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
 158         at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
 159                            | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
 160                            | ATMEL_UART_RI);
 161         at91_add_device_serial();
 162         /* Ethernet */
 163         at91_add_device_eth(&ek_eth_data);
 164         /* USB Host */
 165         at91_add_device_usbh(&ek_usbh_data);
 166         /* USB Device */
 167         at91_add_device_udc(&ek_udc_data);
 168         at91_set_multi_drive(ek_udc_data.pullup_pin, 1);        /* pullup_pin is connected to reset */
 169         /* I2C */
 170         at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
 171         /* SPI */
 172         at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 173 #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
 174         /* DataFlash card */
 175         at91_set_gpio_output(AT91_PIN_PB22, 0);
 176 #else
 177         /* MMC */
 178         at91_set_gpio_output(AT91_PIN_PB22, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
 179         at91_add_device_mmc(0, &ek_mmc_data);
 180 #endif
 181         /* NOR Flash */
 182         platform_device_register(&ek_flash);
 183         /* LEDs */
 184         at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
 185         /* VGA */
 186 //      ek_add_device_video();
 187 }
 188
 189 MACHINE_START(AT91RM9200EK, "Atmel AT91RM9200-EK")
 190         /* Maintainer: SAN People/Atmel */
 191         .timer          = &at91rm9200_timer,
 192         .map_io         = at91_map_io,
 193         .init_early     = ek_init_early,
 194         .init_irq       = at91_init_irq_default,
 195         .init_machine   = ek_board_init,
 196 MACHINE_END