2 * linux/arch/arm/mach-at91/board-neocore926.c
4 * Copyright (C) 2005 SAN People
5 * Copyright (C) 2007 Atmel Corporation
6 * Copyright (C) 2008 ADENEO.
8 * This program is free software; you can redistribute it and/or modify
9 * it under the terms of the GNU General Public License as published by
10 * the Free Software Foundation; either version 2 of the License, or
11 * (at your option) any later version.
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
23 #include <linux/types.h>
24 #include <linux/gpio.h>
25 #include <linux/init.h>
27 #include <linux/module.h>
28 #include <linux/platform_device.h>
29 #include <linux/spi/spi.h>
30 #include <linux/spi/ads7846.h>
32 #include <linux/gpio_keys.h>
33 #include <linux/input.h>
35 #include <video/atmel_lcdc.h>
37 #include <asm/setup.h>
38 #include <asm/mach-types.h>
40 #include <asm/sizes.h>
42 #include <asm/mach/arch.h>
43 #include <asm/mach/map.h>
44 #include <asm/mach/irq.h>
46 #include <mach/hardware.h>
47 #include <mach/board.h>
48 #include <mach/at91sam9_smc.h>
54 static void __init neocore926_init_early(void)
56 /* Initialize processor: 20 MHz crystal */
57 at91_initialize(20000000);
59 /* DBGU on ttyS0. (Rx & Tx only) */
60 at91_register_uart(0, 0, 0);
62 /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
63 at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
65 /* set serial console to ttyS0 (ie, DBGU) */
66 at91_set_serial_console(0);
72 static struct at91_usbh_data __initdata neocore926_usbh_data = {
74 .vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
75 .overcurrent_pin= {-EINVAL, -EINVAL},
81 static struct at91_udc_data __initdata neocore926_udc_data = {
82 .vbus_pin = AT91_PIN_PA25,
83 .pullup_pin = -EINVAL, /* pull-up driven by UDC */
90 #if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
91 static int ads7843_pendown_state(void)
93 return !at91_get_gpio_value(AT91_PIN_PA15); /* Touchscreen PENIRQ */
96 static struct ads7846_platform_data ads_info = {
102 .vref_delay_usecs = 100,
105 .pressure_max = 15000,
108 .debounce_tol = (~0),
109 .get_pendown_state = ads7843_pendown_state,
112 static void __init neocore926_add_device_ts(void)
114 at91_set_B_periph(AT91_PIN_PA15, 1); /* External IRQ1, with pullup */
115 at91_set_gpio_input(AT91_PIN_PC13, 1); /* Touchscreen BUSY signal */
118 static void __init neocore926_add_device_ts(void) {}
124 static struct spi_board_info neocore926_spi_devices[] = {
125 #if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
126 { /* DataFlash card */
127 .modalias = "mtd_dataflash",
129 .max_speed_hz = 15 * 1000 * 1000,
133 #if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
135 .modalias = "ads7846",
137 .max_speed_hz = 125000 * 16,
139 .platform_data = &ads_info,
140 .irq = AT91SAM9263_ID_IRQ1,
149 static struct at91_mmc_data __initdata neocore926_mmc_data = {
151 .det_pin = AT91_PIN_PE18,
152 .wp_pin = AT91_PIN_PE19,
158 * MACB Ethernet device
160 static struct macb_platform_data __initdata neocore926_macb_data = {
161 .phy_irq_pin = AT91_PIN_PE31,
169 static struct mtd_partition __initdata neocore926_nand_partition[] = {
171 .name = "Linux Kernel", /* "Partition 1", */
176 .name = "Filesystem", /* "Partition 2", */
177 .offset = MTDPART_OFS_NXTBLK,
181 .name = "Free", /* "Partition 3", */
182 .offset = MTDPART_OFS_NXTBLK,
183 .size = MTDPART_SIZ_FULL,
187 static struct atmel_nand_data __initdata neocore926_nand_data = {
190 .rdy_pin = AT91_PIN_PB19,
191 .rdy_pin_active_low = 1,
192 .enable_pin = AT91_PIN_PD15,
193 .ecc_mode = NAND_ECC_SOFT,
194 .parts = neocore926_nand_partition,
195 .num_parts = ARRAY_SIZE(neocore926_nand_partition),
199 static struct sam9_smc_config __initdata neocore926_nand_smc_config = {
202 .ncs_write_setup = 0,
207 .ncs_write_pulse = 4,
213 .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
217 static void __init neocore926_add_device_nand(void)
219 /* configure chip-select 3 (NAND) */
220 sam9_smc_configure(0, 3, &neocore926_nand_smc_config);
222 at91_add_device_nand(&neocore926_nand_data);
229 #if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
230 static struct fb_videomode at91_tft_vga_modes[] = {
232 .name = "TX09D50VM1CCA @ 60",
234 .xres = 240, .yres = 320,
235 .pixclock = KHZ2PICOS(5000),
237 .left_margin = 1, .right_margin = 33,
238 .upper_margin = 1, .lower_margin = 0,
239 .hsync_len = 5, .vsync_len = 1,
241 .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
242 .vmode = FB_VMODE_NONINTERLACED,
246 static struct fb_monspecs at91fb_default_monspecs = {
247 .manufacturer = "HIT",
248 .monitor = "TX09D70VM1CCA",
250 .modedb = at91_tft_vga_modes,
251 .modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
258 #define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
259 | ATMEL_LCDC_DISTYPE_TFT \
260 | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
262 static void at91_lcdc_power_control(int on)
264 at91_set_gpio_value(AT91_PIN_PA30, on);
268 static struct atmel_lcdfb_info __initdata neocore926_lcdc_data = {
269 .lcdcon_is_backlight = true,
271 .default_dmacon = ATMEL_LCDC_DMAEN,
272 .default_lcdcon2 = AT91SAM9263_DEFAULT_LCDCON2,
273 .default_monspecs = &at91fb_default_monspecs,
274 .atmel_lcdfb_power_control = at91_lcdc_power_control,
276 .lcd_wiring_mode = ATMEL_LCDC_WIRING_RGB555,
280 static struct atmel_lcdfb_info __initdata neocore926_lcdc_data;
287 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
288 static struct gpio_keys_button neocore926_buttons[] = {
289 { /* BP1, "leftclic" */
291 .gpio = AT91_PIN_PC5,
293 .desc = "left_click",
296 { /* BP2, "rightclic" */
298 .gpio = AT91_PIN_PC4,
300 .desc = "right_click",
305 static struct gpio_keys_platform_data neocore926_button_data = {
306 .buttons = neocore926_buttons,
307 .nbuttons = ARRAY_SIZE(neocore926_buttons),
310 static struct platform_device neocore926_button_device = {
315 .platform_data = &neocore926_button_data,
319 static void __init neocore926_add_device_buttons(void)
321 at91_set_GPIO_periph(AT91_PIN_PC5, 0); /* left button */
322 at91_set_deglitch(AT91_PIN_PC5, 1);
323 at91_set_GPIO_periph(AT91_PIN_PC4, 0); /* right button */
324 at91_set_deglitch(AT91_PIN_PC4, 1);
326 platform_device_register(&neocore926_button_device);
329 static void __init neocore926_add_device_buttons(void) {}
336 static struct ac97c_platform_data neocore926_ac97_data = {
337 .reset_pin = AT91_PIN_PA13,
341 static void __init neocore926_board_init(void)
344 at91_add_device_serial();
347 at91_add_device_usbh(&neocore926_usbh_data);
350 at91_add_device_udc(&neocore926_udc_data);
353 at91_set_gpio_output(AT91_PIN_PE20, 1); /* select spi0 clock */
354 at91_add_device_spi(neocore926_spi_devices, ARRAY_SIZE(neocore926_spi_devices));
357 neocore926_add_device_ts();
360 at91_add_device_mmc(1, &neocore926_mmc_data);
363 at91_add_device_eth(&neocore926_macb_data);
366 neocore926_add_device_nand();
369 at91_add_device_i2c(NULL, 0);
372 at91_add_device_lcdc(&neocore926_lcdc_data);
375 neocore926_add_device_buttons();
378 at91_add_device_ac97(&neocore926_ac97_data);
381 MACHINE_START(NEOCORE926, "ADENEO NEOCORE 926")
382 /* Maintainer: ADENEO */
383 .timer = &at91sam926x_timer,
384 .map_io = at91_map_io,
385 .init_early = neocore926_init_early,
386 .init_irq = at91_init_irq_default,
387 .init_machine = neocore926_board_init,