Pileus Git - ~andy/linux/blob - arch/arm/mach-at91/board-eco920.c

   1 /*
   2  * This program is free software; you can redistribute it and/or modify
   3  * it under the terms of the GNU General Public License as published by
   4  * the Free Software Foundation; either version 2 of the License, or
   5  * (at your option) any later version.
   6  *
   7  * This program is distributed in the hope that it will be useful,
   8  * but WITHOUT ANY WARRANTY; without even the implied warranty of
   9  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  10  * GNU General Public License for more details.
  11  *
  12  * You should have received a copy of the GNU General Public License
  13  * along with this program; if not, write to the Free Software
  14  * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
  15  */
  16
  17 #include <linux/init.h>
  18 #include <linux/platform_device.h>
  19 #include <linux/mtd/physmap.h>
  20 #include <linux/gpio.h>
  21
  22 #include <asm/mach-types.h>
  23
  24 #include <asm/mach/arch.h>
  25 #include <asm/mach/map.h>
  26
  27 #include <mach/board.h>
  28 #include <mach/at91_aic.h>
  29 #include <mach/at91rm9200_mc.h>
  30 #include <mach/at91_ramc.h>
  31 #include <mach/cpu.h>
  32
  33 #include "generic.h"
  34
  35 static void __init eco920_init_early(void)
  36 {
  37         /* Set cpu type: PQFP */
  38         at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
  39
  40         at91_initialize(18432000);
  41 }
  42
  43 static struct macb_platform_data __initdata eco920_eth_data = {
  44         .phy_irq_pin    = AT91_PIN_PC2,
  45         .is_rmii        = 1,
  46 };
  47
  48 static struct at91_usbh_data __initdata eco920_usbh_data = {
  49         .ports          = 1,
  50         .vbus_pin       = {-EINVAL, -EINVAL},
  51         .overcurrent_pin= {-EINVAL, -EINVAL},
  52 };
  53
  54 static struct at91_udc_data __initdata eco920_udc_data = {
  55         .vbus_pin       = AT91_PIN_PB12,
  56         .pullup_pin     = AT91_PIN_PB13,
  57 };
  58
  59 static struct at91_mmc_data __initdata eco920_mmc_data = {
  60         .slot_b         = 0,
  61         .wire4          = 0,
  62         .det_pin        = -EINVAL,
  63         .wp_pin         = -EINVAL,
  64         .vcc_pin        = -EINVAL,
  65 };
  66
  67 static struct physmap_flash_data eco920_flash_data = {
  68         .width  = 2,
  69 };
  70
  71 static struct resource eco920_flash_resource = {
  72         .start          = 0x11000000,
  73         .end            = 0x11ffffff,
  74         .flags          = IORESOURCE_MEM,
  75 };
  76
  77 static struct platform_device eco920_flash = {
  78         .name           = "physmap-flash",
  79         .id             = 0,
  80         .dev            = {
  81                 .platform_data  = &eco920_flash_data,
  82         },
  83         .resource       = &eco920_flash_resource,
  84         .num_resources  = 1,
  85 };
  86
  87 static struct spi_board_info eco920_spi_devices[] = {
  88         {       /* CAN controller */
  89                 .modalias       = "tlv5638",
  90                 .chip_select    = 3,
  91                 .max_speed_hz   = 20 * 1000 * 1000,
  92                 .mode           = SPI_CPHA,
  93         },
  94 };
  95
  96 static void __init eco920_board_init(void)
  97 {
  98         /* Setup the LEDs */
  99         at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
 100         /* DBGU on ttyS0. (Rx & Tx only */
 101         at91_register_uart(0, 0, 0);
 102         at91_add_device_serial();
 103         at91_add_device_eth(&eco920_eth_data);
 104         at91_add_device_usbh(&eco920_usbh_data);
 105         at91_add_device_udc(&eco920_udc_data);
 106
 107         at91_add_device_mmc(0, &eco920_mmc_data);
 108         platform_device_register(&eco920_flash);
 109
 110         at91_ramc_write(0, AT91_SMC_CSR(7),     AT91_SMC_RWHOLD_(1)
 111                                 | AT91_SMC_RWSETUP_(1)
 112                                 | AT91_SMC_DBW_8
 113                                 | AT91_SMC_WSEN
 114                                 | AT91_SMC_NWS_(15));
 115
 116         at91_set_A_periph(AT91_PIN_PC6, 1);
 117
 118         at91_set_gpio_input(AT91_PIN_PA23, 0);
 119         at91_set_deglitch(AT91_PIN_PA23, 1);
 120
 121 /* Initialization of the Static Memory Controller for Chip Select 3 */
 122         at91_ramc_write(0, AT91_SMC_CSR(3),
 123                 AT91_SMC_DBW_16  |      /* 16 bit */
 124                 AT91_SMC_WSEN    |
 125                 AT91_SMC_NWS_(5) |      /* wait states */
 126                 AT91_SMC_TDF_(1)        /* float time */
 127         );
 128
 129         at91_add_device_spi(eco920_spi_devices, ARRAY_SIZE(eco920_spi_devices));
 130 }
 131
 132 MACHINE_START(ECO920, "eco920")
 133         /* Maintainer: Sascha Hauer */
 134         .timer          = &at91rm9200_timer,
 135         .map_io         = at91_map_io,
 136         .handle_irq     = at91_aic_handle_irq,
 137         .init_early     = eco920_init_early,
 138         .init_irq       = at91_init_irq_default,
 139         .init_machine   = eco920_board_init,
 140 MACHINE_END